Search your favorite song right now

1. S02E01 - Lathe Rebuild Part 1

  • Published: 1 year ago
  • Duration: 9:11
  • By
S02E01 - Lathe Rebuild Part 1

It's big and heavy, but how much of that is rust? Or eggs? Today we start a total refurbishment of a 1960's era Colchester Bantam ...


2. S02E02 - Lathe Rebuild Part 2 (6 Ways To Remove Rust)

  • Published: 1 year ago
  • Duration: 6:21
  • By
S02E02 - Lathe Rebuild Part 2 (6 Ways To Remove Rust)

Things used: Evaporust: available at most auto parts stores. Electrolysis setup: positive lead goes on the sacrificial steel, negative ...


3. S02E03 - Lathe Rebuild Part 3

  • Published: 1 year ago
  • Duration: 6:04
  • By
S02E03 -  Lathe Rebuild Part 3

I think we've finally taken as much apart as we're going to take apart. Think we can put it back together? Patreon page: ...


4. S02E04 - Lathe Rebuild Part 4

  • Published: 1 year ago
  • Duration: 6:07
  • By
S02E04 - Lathe Rebuild Part 4

Work continues on the lathe. This week we start some of the painting. I give some (bad?) advice on spray paint technique and we ...


5. S02E07 - Lathe Rebuild Part 7

  • Published: 1 year ago
  • Duration: 10:44
  • By
S02E07 - Lathe Rebuild Part 7

Its finally being put back together! well some if it anyway. A Few Notes: The measurements we were getting on the level showed ...


6. Colchester Lathe (1964) Re-furbishment Part 1

  • Published: 1 year ago
  • Duration: 11:50
  • By
Colchester Lathe (1964) Re-furbishment Part 1

This is a strip down and refurbishment of a 1964 Colchester Student lathe I purchased to replace the Winfield Lathe destroyed in ...


7. Machining Lathe Riser Feet Part 1

  • Published: 3 years ago
  • Duration: 25:11
  • By
Machining Lathe Riser Feet Part 1

In this new two part series, I begin the lathe work on the risers I want to make for the Victor lathe. We'll have some indicating, and ...


8. South Bend Lathe Rebuild Part 1

  • Published: 4 months ago
  • Duration: 23:03
  • By
South Bend Lathe Rebuild Part 1

Rebuilding a model 10L South Bend Lathe Part 1 Heavy 10 Introduction and History.


9. S02E14 - Lathe Rebuild Part 11

  • Published: 10 months ago
  • Duration: 13:31
  • By
S02E14 - Lathe Rebuild Part 11

The Lathe is finished!!! (mostly). I think it looks great, and even cuts pretty well. I reworked some of the wiring, and built a motor ...


10. Portass lathe restoration part 1

  • Published: 1 year ago
  • Duration: 5:01
  • By

11. Vintage Lathe Restoration: Part 1

  • Published: 1 year ago
  • Duration: 9:36
  • By
Vintage Lathe Restoration: Part 1

This is an old lathe that I got from a friend for pretty much nothing, I do not know much about it but as soon as I find out more I will ...


12. Standard Modern 12 Inch Lathe Restoration Part 1

  • Published: 2 years ago
  • Duration: 13:48
  • By
Standard Modern 12 Inch Lathe Restoration Part 1

A Standard Modern 12 inch Lathe is brought home and the restoration begins.


13. American Lathe Restoration Project Part 1

  • Published: 1 year ago
  • Duration: 14:33
  • By
American Lathe Restoration Project Part 1

The first part in a series on old American Lathe restoration project. In this chapter I review lathe and what I plan on doing in overall ...


14. colchester lathe cross slide repair part one

  • Published: 3 years ago
  • Duration: 13:47
  • By
colchester lathe cross slide repair part one

Colchester student lathe repair part one.


15. Porter McLeod Lathe Restoration - Part 1: Overview

  • Published: 1 year ago
  • Duration: 11:57
  • By
Porter McLeod Lathe Restoration - Part 1: Overview

A first of a series of videos dedicated to the restoration of the Porter McLeod lathe. Please like, comment, subscribe and share this ...


16. S02E10 - Lathe Rebuild Part 9

  • Published: 11 months ago
  • Duration: 11:23
  • By
S02E10 - Lathe Rebuild Part 9

I promise it's not just ten minutes of scraping. It's eleven minutes of scraping. Patreon page: ...


17. How to Rebuild Half Nuts for Logan 10" Lathe part 2

  • Published: 11 months ago
  • Duration: 19:57
  • By
How to Rebuild Half Nuts for Logan 10" Lathe  part 2

I finished rebuilding the half nuts for my Logan 10" lathe. This process should work for other small lathes like Southbend or Atlas ...


18. S02E08 - Lathe Rebuild Part 8

  • Published: 1 year ago
  • Duration: 11:28
  • By
S02E08 - Lathe Rebuild Part 8

This week we find out just how bad our lathe really is. How many dial indicators is too many dial indicators? Is there such a thing?


19. How to Rebuild Half Nuts for Logan 10" Lathe part 1

  • Published: 1 year ago
  • Duration: 14:53
  • By
How to Rebuild Half Nuts for Logan 10" Lathe  part 1

I start rebuilding a spare set of half nuts for my Logan 10" lathe.


20. S02E05 - Lathe Rebuild Part 5

  • Published: 1 year ago
  • Duration: 5:45
  • By
S02E05 - Lathe Rebuild Part 5

This week we break out the big (paint) guns. Professional paint equipment and an amateur painter, what could go wrong. Patreon ...