Search your favorite song right now

1. Make a tool rest - part 3 - Materials

  • Published: 3 years ago
  • Duration: 11:19
  • By
Make a tool rest - part 3 - Materials

In the third video of my series on how to make a tool rest for your woodturning lathe (without welding!), I describe the materials ...


2. Make a tool rest - part 5 - Cutting

  • Published: 3 years ago
  • Duration: 28:07
  • By
Make a tool rest - part 5 - Cutting

In the fifth video of my series on how to make a tool rest for your woodturning lathe (without welding!), I show how to cut the metal ...


3. Make a tool rest - part 2 - Tools

  • Published: 3 years ago
  • Duration: 15:50
  • By
Make a tool rest - part 2 - Tools

In the second video of my series on how to make a tool rest for your woodturning lathe (without welding!), I describe the different ...


4. Make a tool rest - part 1 - overview

  • Published: 3 years ago
  • Duration: 11:50
  • By
Make a tool rest - part 1 - overview

Woodturning: Make a tool rest of any length for your woodturning lathe, using silver brazing. No welding required! Jan 23 2016 ...


5. Make a tool rest - part 4 - Sizing

  • Published: 3 years ago
  • Duration: 17:04
  • By
Make a tool rest - part 4 - Sizing

In the fourth video of my series on how to make a tool rest for your woodturning lathe (without welding!), I describe how to ...


6. #141 DIY Woodturning Tool Rest

  • Published: 5 months ago
  • Duration: 15:23
  • By
#141 DIY Woodturning Tool Rest

Building accessories for my lathe includes some new tool rests. This is the first of probably three.


7. Real Lathe Pt. 4: Fully Adjustable Tool-rest

  • Published: 3 months ago
  • Duration: 14:50
  • By
Real Lathe Pt. 4: Fully Adjustable Tool-rest

More video and exclusive content: http://www.patreon.com/rexkrueger Rex Krueger t-shirts and hoodies: ...


8. Adjusting The Tool Rest - Part 3 (conclusion)

  • Published: 1 year ago
  • Duration: 6:56
  • By
Adjusting The Tool Rest - Part 3 (conclusion)

Adjusting the height of my small tool-rest so that it will fit my lathe.


9. Because I Can Part Three

  • Published: 4 months ago
  • Duration: 56:58
  • By
Because I Can Part Three

Removing the material on new Main bearing caps to match block bore on Audi 2.1 L 5 cylinder. Part Three, Where the bit hits the ...


10. Field Expedient Steady Rest Part 1

  • Published: 2 months ago
  • Duration: 32:01
  • By
Field Expedient Steady Rest Part 1

To move forward with the Long Fat Turning demonstration, I take time out to make a steady rest. This video is intended mainly for ...


11. Make a tool rest - part 6 - Brazing

  • Published: 3 years ago
  • Duration: 23:04
  • By
Make a tool rest - part 6 -  Brazing

In this sixth and final video in my series of videos about making a tool rest (without welding!), I braze the arm to the post, and then ...


12. Lathe tool rest from scratch

  • Published: 1 year ago
  • Duration: 3:29
  • By
Lathe tool rest from scratch

Instead of buying a new tool rest, I decided to make one.


13. The grinder stand project part 3

  • Published: 11 months ago
  • Duration: 25:55
  • By
The grinder stand project part 3

I am starting a series on making an aluminum tool rest stands for my Baldor bench grinder that I purchased at an auction a few ...


14. How to setup Wilton Baby Bullet Alternative Part 3 Final

  • Published: 3 years ago
  • Duration: 40:31
  • By
How to setup Wilton Baby Bullet Alternative Part 3 Final

This is Part 3 Final to the Baby Bullet alternative vise build. This project is an alternative project to buying or building (See Tom ...


15. Round tool rest for your lathe

  • Published: 4 years ago
  • Duration: 7:30
  • By
Round tool rest for your lathe

I have a 12 year old lathe that has a less than desirable tool rest on it. I have seen the round tool rests online for $25 and up but ...


16. 36 - Fabricating Some Tool Rests

  • Published: 1 year ago
  • Duration: 20:05
  • By
36 - Fabricating Some Tool Rests

I fabricate some tool rests for hollowing from basic steel stock, two of which are captive rests, for use with my longer carbide ...


17. The Catch That Broke The Tool Rest

  • Published: 2 years ago
  • Duration: 0:11
  • By
The Catch That Broke The Tool Rest

By the looks of this a double catch that threw the skew into the chuck and then forced it down onto the tool rest snapping it off.


18. The grinder stand project part 2

  • Published: 11 months ago
  • Duration: 16:39
  • By
The grinder stand project part 2

I am starting a series on making an aluminum tool rest stands for my Baldor bench grinder that I purchased at an auction a few ...


19. DIY Turning Tool Rest

  • Published: 4 months ago
  • Duration: 2:56
  • By
DIY Turning Tool Rest

A quick overview of a homemade wood turning tool rest. Grizzly T25920.


20. DIY tool rest for sharpening with the vertical belt sander

  • Published: 4 months ago
  • Duration: 5:37
  • By
DIY tool rest for sharpening with the vertical belt sander

I have a grinder / belt sander combo machine. I use this machine, mostly for sharpening. In this video I make a tool rest for the ...